series am8t-z 8 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.g 1 of 3 north america only features: models single output model input voltage (v) output voltage (v) output current max (ma) capacitive load ( f) efficiency (%) am8t-1203sz 9-18 3.3 2000 3300 80 am8t-1205sz 9-18 5 1500 2200 82 am8t-1212sz 9-18 12 665 470 85 am8t-1215sz 9-18 15 535 220 83 am8t-2403sz 18-36 3.3 2000 3300 80 am8t-2405sz 18-36 5 1500 2200 82 am8t-2412sz 18-36 12 665 470 85 am8t-2415sz 18-36 15 535 220 84 AM8T-4803SZ 36-72 3.3 2000 3300 80 am8t-4805sz 36-72 5 1500 2200 82 am8t-4812sz 36-72 12 665 470 84 am8t-4815sz 36-72 15 535 220 84 models dual output model input voltage (v) output voltage (v) output current max (ma) capacitive load ( f) efficiency (%) am8t-1205dz 9-18 5 800 1000 82 am8t-1212dz 9-18 12 335 220 84 am8t-1215dz 9-18 15 265 100 84 am8t-2405dz 18-36 5 800 1000 82 am8t-2412dz 18-36 12 335 220 83 am8t-2415dz 18-36 15 265 100 85 am8t-4805dz 36-72 5 800 1000 82 am8t-4812dz 36-72 12 335 220 85 am8t-4815dz 36-72 15 265 100 85 input specifications parameters nominal typical maximum units voltage range 12 9-18 vdc 24 18-36 48 36-72 filter ? ? ? rohs compliant ? ? 24 pin dip package ? ? wide 2:1 input range ? ? efficiency up to 85% ?
series am8t-z 8 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.g 2 of 3 north america only isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 1500 vdc case/input & output 1000 vdc resistance > 1000 mohm capacitance 1000 pf output specifications parameters conditions typical maximum units voltage accuracy 1 % voltage balance (dual output model) balanced load 1 % short circuit protection continuous short circuit restart auto recovery current limiting 140 % of iout max line voltage regulation hl-ll 0.5 % load voltage regulation 10% to 100% load 0.5 % temperature coefficient 0.02 %/ o c rising time 10 ms ripple and noise 75 mvp-p general specifications parameters conditions typical maximum units switching frequency 100% load 330 khz operating temperature with derating above 55c -40 to +85 o c storage temperature -40 to +125 o c max case temperature +100 o c cooling free air convection humidity 95 % case material nickel coated cooper weight 17 g dimensions (l x h x w) tolerance 0.5 mm or 0.02 inches 1.25 x 0.80 x 0.40 inches 31.80 x 20.30 x 10.20 mm mtbf >1 121 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. safety specifications parameters agency approval ce standards iec 60950-1:2005 (2 n d edition); en 60950-1:2006 en55022 class a, en55024 iec61000-4-2, perf. criteria b iec61000-4-3, perf. criteria a iec61000-4-4, perf. criteria b (e xternal 220uf/100v cap required) iec61000-4-5, perf. criteria b (e xternal 220uf/100v cap required) iec61000-4-6, perf. criteria a iec61000-4-8, perf. criteria a
series am8t-z 8 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.g 3 of 3 north america only pin out specifications dimensions (bottom view) 20.30 (0.80) 10.20 (0.40) 3.05 (0.12) 15.24 (0.60) derating test circuits conducted emissions: note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com. pin single dual 2 -v input -v input 3 -v input -v input 9 no pin common 11 n.c. -v output 14 +v output + v output 16 -v output common 22 +v input +v input 23 +v input +v input
|
